NAME

       grdreformat - Converting between different grdfile formats.

SYNOPSIS

       grdreformat       ingrdfile[=id[/scale/offset[/NaNvalue]]]      outgrd-
       file[=id[/scale/offset[/NaNvalue]]]
        [ -N ] [ -Rwest/east/south/north[r] ] [ -V ]

DESCRIPTION

       grdreformat reads a grdfile in one  format  and  writes  it  out  using
       another  format.  As an option the user may select a subset of the data
       to be written and to specify scaling, translation, and NaN-value.

       ingrdfile
              The grdfile to be read. Append format =id number if not a  stan-
              dard GMT netCDF-based grdfile.  If id is set, you may optionally
              append scale and offset to scale the data and then add  an  off-
              set.  If  scale  and  offset  are supplied you may also append a
              value that represent ’not-a-number’  (for  floating-point  grids
              this  is  unnecessary  since the IEEE NaN is used; however short
              integers need a value which means no data available.)

       outgrdfile
              The grdfile to be written. Append format =id  number  if  not  a
              standard  GMT  netCDF-based  grdfile.   If  id  is  set, you may
              optionally append scale and offset to scale the  data  and  then
              add  an  offset.  If  scale and offset are supplied you may also
              append a value that represent ’not-a-number’ (for floating-point
              grids  this  is  unnecessary since the IEEE NaN is used; however
              short integers need a value which means no data available.)  For
              format  =id  >  0 the size of the GMT grdheader block is hsize =
              896 bytes, and the total size of the file is hsize + nx *  ny  *
              item_size,  where item_size is the size in bytes of each element
              (1, 2, 4). Bit grids are  stored  using  4-byte  integers,  each
              holding  32  bits, so for these files the size equation is modi-
              fied by using ceil (nx / 32) * 4 instead of nx. For  header  and
              grid details, see Appendix B.

OPTIONS

       -N     Suppress the writing of the GMT header structure. This is useful
              when you want to write a native grid to be used by grdraster. It
              only applies to native grids and is skipped for netCDF output.

       -R     xmin,  xmax,  ymin, and ymax specify the Region of interest. For
              geographic regions,  these  limits  correspond  to  west,  east,
              south,  and north and you may specify them in decimal degrees or
              in [+-]dd:mm[:ss.xxx][W|E|S|N] format. Append r  if  lower  left
              and  upper  right map coordinates are given instead of wesn. The
              two shorthands  -Rg  -Rd  stand  for  global  domain  (0/360  or
              -180/+180  in longitude respectively, with -90/+90 in latitude).
              For calendar time coordinates you may either give relative  time
              (relative  to  the  selected  TIME_EPOCH  and  in  the  selected
              TIME_UNIT; append t to -JX|x), or  absolute  time  of  the  form
              [date]T[clock]  (append  T  to  -JX|x). At least one of date and
              clock must be present; the T is always required. The date string
              must  be  of  the form [-]yyyy[-mm[-dd]] (Gregorian calendar) or
              yyyy[-Www[-d]] (ISO week calendar), while the clock string  must
              be  of  the form hh:mm:ss[.xxx]. The use of delimiters and their
              type and positions must be as indicated  (however,  input/output
              and plotting formats are flexible).

       -V     Selects verbose mode, which will send progress reports to stderr
              [Default runs "silently"].

EXAMPLES

       To create a 4-byte  raw  floating  point  grid  from  the  netCDF  file
       data.grd:

       grdreformat data.grd ras_data.b4=1 -V

       To  make  a  2-byte short integer file, scale it by 10, subtract 32000,
       setting NaNs to -9999, do

       grdreformat values.grd shorts.i2=2/10/-32000/-9999 -V

       To create a Sun standard 8-bit rasterfile for a subset of the data file
       image.grd,  assuming  the  range in image.grd is 0-1 and we need 0-255,
       run

       grdreformat image.grd -R-60/-40/-40/-30 image.ras8=3/255/0 -V

       To convert etopo2.grd to etopo2.i2 that can be used by grdraster, try

       grdreformat etopo2.grd etopo2.i2=2 -N -V

SEE ALSO

       gmt(l), grdmath(l)



GMT4.0                            1 Oct 2004                    GRDREFORMAT(l)